Rod Seal

FR200 - Rod Seal

General Features
Technicial Specifications

KASTAŞ NO	d (f8)	D (H11)	b	B (-0/+0,2)	n
FR200-016	16	24	5.67	6,3	2
FR200-018	18	26	5.67	6,3	2
FR200-020	20	28	5.67	6,3	2
FR200-022	22	30	5.67	6,3	3
FR200-022/1	22	32	7.2	8	3
FR200-025	25	33	5.67	6,3	3
FR200-025/1	25	35	7.2	8	3
FR200-028	28	36	5.67	6,3	3
FR200-028/1	28	38	7.2	8	3
FR200-030	30	40	7.2	8	3
FR200-032	32	42	7.2	8	3
FR200-036	36	46	7.2	8	3
FR200-040	40	50	7.2	8	3.5
FR200-045	45	55	7.2	8	3.5
FR200-050	50	60	7.2	8	3.5
FR200-055	55	65	7.2	8	4.5
FR200-056	56	71	11.25	12,5	4.5
FR200-060/1	60	75	11.25	12,5	4.5
FR200-063	63	78	11.25	12,5	4.5
FR200-065	65	75	7.2	8	4.5
FR200-070	70	85	11.25	12,5	4.5
FR200-080	80	95	11.25	12,5	5
FR200-090	90	105	11.25	12,5	5
FR200-100	100	120	14.4	16	5

FR200 is a single acting rod seal, which is designed to ensure low friction force, reliable backpumping ability and superior sealing.

PRODUCT ADVANTAGES
• Superior static and dynamic sealing
• Low friction capability
• Increased extrusion resistance
• Reliable backpumping ability
• Operates well with a double wiper without a problem

APPLICATION
Construction machinery , fork-lift trucks , injection moulding machines , all hydraulic applications that need low friction force, metal working machines

MATERIAL		CODE
PU	94 SHORE A	PU9401

OPERATING CONDITIONS
MEDIA	Mineral oils(DIN 51524)	HFA and HFB	HFC
TEMPERATURE	-35°C +100°C	+5°C +50°C	-30°C +40°C
PRESSURE	≤400 Bar	≤400 Bar	≤400 Bar
SPEED	≤0.5 m/sn	≤0.5 m/sn	≤0.5 m/sn
Note: The above data are maximum values and cannot be used at the same time.

SURFACE ROUGHNESS	Ra	Rmax
Sliding Surface Ød	0.05≤..≤0.4 μm	≤3.2 μm
Groove Base ØD	0.20≤..≤1.6 μm	≤10 μm
Groove Flanks B	0.20≤..≤3.2 μm	≤16 μm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
INSTALLATION Existing table values of K22 rod sealing element should be used to decide closed groove dimensions. Open grooves or special assembly tools should be used for the values that are outside this table. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the rod seal must be oiled with system oil.

PERMISSIBLE SEALING GAP

Smax (mm)

t=(D-d)/2(mm)	150 Bar	250 Bar	400 Bar
t≤5	0.50	0.45	0.25
t>5	0.60	0.45	0.35

Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.