K01

Rod Packing
Rod Packing
   KASTAŞ NO d(f8) D(H9) B(-0/+0,2) n
 K01-008 8 18 18,5 4
 K01-010 10 20 18,5 4
 K01-012 12 22 18,5 4
 K01-013 13,5 25 16,5 4
 K01-014 14 24 18,5 4
 K01-015 15 25 18,5 4
 K01-015/1 15 32 25 6
 K01-016 16 26 18,5 4
 K01-018 18 28 18,5 4
 K01-018/1 18 32 23,5 4
 K01-020 20 30 18,5 4
 K01-020/1 20 32 22,5 4
 K01-022 22 32 18,5 4
 K01-022/1 22 34 22,5 4
 K01-025 25 37 22,5 4
 K01-025/1 25 40 22,5 6
 K01-028 28 40 22,5 4
 K01-028/1 28 43 22,5 6
 K01-030 30 42 22,5 4
 K01-030/1 30 45 22,5 6
 K01-030/2 30 50 37 6
 K01-032 32 44 22,5 4
 K01-032/1 32 47 22,5 6
 K01-032/2 32 45 22,5 4
 K01-035 35 47 22,5 4
 K01-035/1 35 50 22,5 6
 K01-036 36 48 22,5 4
 K01-036/1 36 51 22,5 6
 K01-040 40 52 22,5 4
 K01-040/1 40 55 22,5 6
 K01-040/2 40 55 25 6
 K01-040/3 40 56 22,5 6
 K01-042 42 54 22,5 4
 K01-042/1 42 57 22,5 6
 K01-045 45 60 22,5 6
 K01-045/1 45 65 22,5 6
 K01-045/2 45 55 22 4
 K01-045/3 45 62 26 6
 K01-047 47 65 33 6
 K01-048 48 63 22,5 6
 K01-050 50 65 22,5 6
 K01-050/1 50 70 30 6
 K01-055 55 70 22,5 6
 K01-055/1 55 75 30 6
 K01-055/2 55 67 24 4
 K01-056 56 71 22,5 6
 K01-056/1 56 76 37 6
 K01-056/2 56 72 46 6
 K01-060 60 75 22,5 6
 K01-060/1 60 80 37 6
 K01-060/3 60 85 37 8
 K01-063 63 78 22,5 6
 K01-063/1 63 83 37 6
 K01-063/2 63,5 78 40 4
 K01-065 65 80 22,5 6
 K01-065/1 65 85 40 6
 K01-070 70 85 22,5 6
 K01-070/1 70 90 40 6
 K01-075 75 90 22,5 6
 K01-075/1 75 95 40 6
 K01-075/2 75 87 25 4
 K01-075/3 75 100 34 8
 K01-078 78 100 35 7
 K01-080 80 95 22,5 6
 K01-080/1 80 100 40 6
 K01-085 85 100 22,5 6
 K01-085/1 85 105 40 6
 K01-085/2 85 95 22,5 4
 K01-090 90 105 22,5 6
 K01-090/1 90 110 40 6
 K01-090/2 90 110 26 6
 K01-090/3 90 110 22,5 6
 K01-095 95 120 50 8
 K01-100 100 115 30 6
 K01-100/1 100 120 40 6
 K01-105 105 120 30 6
 K01-105/1 105 125 40 6
 K01-105/2 105 130 40 8
 K01-110 110 125 30 6
 K01-110/1 110 130 40 6
 K01-115 115 130 30 6
 K01-115/1 115 140 46 6
 K01-115/2 115 135 30 8
 K01-120 120 140 49 6
 K01-120/1 120 145 46 8
 K01-125 125 140 34 6
 K01-125/1 125 150 46 8
 K01-130 130 155 42,5 8
 K01-135 135 160 55 8
 K01-135/1 135 160 40 8
 K01-140 140 155 34 6
 K01-140/1 140 165 46 8
 K01-140/2 140 160 32 6
 K01-140/3 140 170 60 8
 K01-150 150 170 40 6
 K01-150/1 150 180 60 8
 K01-160 160 180 40 6
 K01-160/1 160 190 60 8
 K01-160/2 160 175 34 4
 K01-165 165 195 50,5 8
 K01-170 170 190 40 6
 K01-180 180 200 40 6
 K01-180/1 180 210 60 8
 K01-190 190 220 42 8
 K01-200 200 220 40 6
 K01-200/1 200 230 60 8
 K01-210 210 240 50 8
 K01-215 215 245 41 8
 K01-220 220 240 40 6
 K01-230 230 260 58 8
 K01-240 240 270 60 8
 K01-240/1 240 260 46 6
 K01-250 250 270 42 6
 K01-260 260 290 60 8
 K01-300 300 330 60 8
 K01-310 310 340 60 8
 K01-320 320 350 60 8
 K01-320/1 320 360 46 12
 K01-330 330 360 60 8
 K01-360 360 390 60 8
 K01-360/1 360 400 55 12
 K01-370 370 400 55 8
 K01-400 400 440 65 12
 K01-400/1 400 430 46 8
 K01-420 420 460 80 12
 K01-440 440 480 68 12
 K01-450 450 490 65 12

K01 is a seven piece single acting sealing set which consists of one reinforced cotton fabric backup ring , one thermoplastic header ring , three reinforced cotton fabric middle rings , and two elastomeric nitrile rubber middle rings.

PRODUCT ADVANTAGES
• Adjustable seal housing height due to the reason of being usedin open grooves.
• Functions even with poor surfaces
• Robust seal
• Easy installation and removal
• Long service life
• Able to work until the maintenance of continuity systemsbecause of the adjustable housing
• Very good sealing performance both in high and low pressures

APPLICATION
Used especially in hard working conditions such as iron and steel industry , mining equipment , marine hydraulics , scrap cutters and special cylinders where the actual conditions are difficult to predict.
MATERIAL   CODE
NBR 80 SHORE A NB9001
COTTON FABRIC NBR   FB8001
POM   PM9903
OPERATING CONDITIONS
MEDIA Mineral oils(DIN 51524)  HFA and HFB HFC
TEMPERATURE -30°C +105°C +5°C +60°C -30°C +60°C
PRESSURE ≤400 Bar ≤400 Bar ≤400 Bar
SPEED ≤0.5 m/sn ≤0.5 m/sn ≤0.5 m/sn
Note: The above data are maximum values and cannot be used at the same time.

    

 
SURFACE ROUGHNESS Ra Rmax
Sliding Surface Ød ≤0.4 μm ≤3.2 μm
Groove Base ØD ≤1.6 μm ≤6.3 μm
Groove Flanks B ≤3.2 μm ≤16 μm
Note: It is recommended to have 50% to 90% of the working surface material contact area value.
 

INSTALLATION
Being assembled in adjustable housing , the groove housing should have an adjustability of 7.5% of the seal height. If there is a requirement of being used in closed housings , individual parts should be cut with 45° angle and staggered by 75° angle at installation. When strongly squeezed , the flexibility of the sealing set may be substantially reduced. This could cause excessive friction force , high wear and vibrated operating under low pressures. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation all individual parts of the seal must be oiled with system oil.
 

NOTES
For special applications that require high temperatures , our seal set is being manufactured in the following configuration , reinforced cotton fabric with FKM for header and middle rings and special mixture of PTFE backup ring. Permissible sealing gap S value should not be above 0.15 mm. For inner diameters above 200 mm , all the middle rings are being produced from reinforced cotton fabric with NBR material. Additional middle rings can be used depending on the application.