Piston Packing

K03 - Piston Packing

General Features
Technicial Specifications

KASTAŞ NO	D (H9)	d (h11)	B(-0/+0,2)	d1(-0,3/+0)	n
K03-020	20	10	9,3	19,5	6
K03-022	22	12	9,3	21,5	6
K03-025	25	15	9,3	24,5	6
K03-028	28	18	9,3	27,5	6
K03-030	30	20	9,3	29,5	6
K03-032	32	20	10,9	31	6
K03-035	35	23	10,9	34	6
K03-036	36	24	10,9	35	6
K03-040	40	25	11,5	39	6
K03-042	42	27	11,5	41	6
K03-045	45	30	11,5	44	6
K03-050	50	35	11,5	49	6
K03-055	55	40	11,5	54	6
K03-056	56	41	11,5	55	6
K03-060	60	45	11,5	59	6
K03-063	63	48	13	62	6
K03-070	70	50	15,2	69	7
K03-080	80	60	15,2	79	7
K03-090	90	70	21,2	89	7
K03-100	100	80	21,2	99	7
K03-110	110	90	21,2	109	7
K03-115	115	95	21,2	114	7
K03-125	125	100	25,8	124	8
K03-140	140	115	25,8	139	8
K03-150	150	120	29	148,5	8
K03-160	160	130	29	158,5	8
K03-180	180	150	31,5	178,5	8
K03-200	200	170	33,5	198,5	8
K03-250	250	220	33,5	248,5	8
K03-275	275	245	33,5	273,5	8
K03-280	280	250	33,5	278,5	8
K03-300	300	270	33,5	298,5	8

K03 is a three piece single acting sealing set which consists of one reinforced cotton fabric backup ring , one elastomeric nitrile rubber middle ring , and one thermoplastic header ring.

PRODUCT ADVANTAGES
• Functions even with poor surfaces
• Easy installation
• Adjustable seal housing height due to the reason of being used in open grooves.

APPLICATION
Used especially in hard working conditions such as iron and steel industry , mining equipment , marine hydraulics , scrap cutters and special cylinders where the actual conditions are difficult to predict.

MATERIAL		CODE
COTTON FABRIC NBR		NB^₈₀₀₈
POM		PM^₉₉₀₃

OPERATING CONDITIONS

MEDIA

Mineral oils(DIN 51524)

HFA and HFB

HFC

TEMPERATURE

-30°C +105°C

+5°C +60°C

-30°C +60°C

PRESSURE

≤400 Bar

SPEED

≤0.5 m/sn

Note: The above data are maximum values and cannot be used at the same time.

SURFACE ROUGHNESS	Ra	Rmax
Sliding Surface Ød	≤0.4 μm	≤3.2 μm
Groove Base ØD	≤1.6 μm	≤6.3 μm
Groove Flanks B	≤3.2 μm	≤16 μm
Note: It is recommended to have 50% to 90% of the working surface material contact area value
INSTALLATION Suitable for open piston housing. When strongly squeezed , the flexibility of the sealing set may be substantially reduced. This could cause by excessive friction force , high wear and vibrated operating under low pressures. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation all individual parts of the seal must be oiled with system oil.
NOTES For special applications that require high temperatures , our seal set is being manufactured with reinforced cotton fabric with FKM and special mixture of PTFE backup ring. Additional middle rings can be used depending on the application.