Pneumatic Piston Seal

KASTAŞ NO	NBR	PU	D (H11)	d (h9)	B (-0/+0,2)	b	d1 (-0/+0,2)
K50-016	NBR	PU	16	10	3,5	3	15
K50-024	NBR		24	16	6	5,5	23
K50-025/1	NBR		25	17	6	5,5	24
K50-028	NBR		28	20	4,5	4	27
K50-032	NBR	PU	32	24	6	5,5	30,5
K50-035 PU		PU	35	27	4,5	4	33,5
K50-036		PU	36.51	25.4	8.95	7.95	35
K50-036/1 PU		PU	36	26	7,5	7	34,5
K50-038		PU	38,1	30,16	7,64	7,14	36,6
K50-040	NBR	PU	40	30	7,5	7	38,5
K50-042		PU	42	30	11	10	40,5
K50-050	NBR	PU	50	40	7,5	7	48,5
K50-050/1	NBR	PU	50	36	7,5	7	48,5
K50-050/3		PU	50	39,29	10,52	9,52	48,5
K50-050/4		PU	50,8	40,54	7,64	7,14	49,3
K50-050/5		PU	50.08	41.27	7.64	7.14	48.58
K50-053		PU	53,97	44,45	6,85	6,35	52,47
K50-057	NBR	PU	57,15	44,45	8,93	7,93	55,65
K50-060	NBR		60	47	9	8	58,5
K50-063	NBR	PU	63	53	7,5	7	61,5
K50-063/1		PU	63,1	46,3	8,1	7,6	61,6
K50-063/3		PU	63,5	51,19	11,31	10,31	62
K50-063/4		PU	63,5	50	8,95	7,95	48,5
K50-066		PU	66,67	57,15	8,94	7,94	65,17
K50-069		PU	69,85	53,97	10,52	9,52	68,35
K50-076		PU	76,2	58,3	14,89	13,89	74,7
K50-080	NBR	PU	80	68	9,5	8,5	78,5
K50-080/2		PU	80	67.3	6.85	6.35	78.5
K50-080/3	NBR		80	62	13,7	12,7	78,5
K50-082		PU	82,55	70,64	9,73	8,73	81,05
K50-093		PU	93	81	9.5	8.5	91.5
K50-098		PU	98.42	86.51	10.5	9.52	96.42
K50-100	NBR	PU	100	88	9,5	8,5	98
K50-101		PU	101,6	83,56	13,7	12,7	99,6
K50-115	NBR		115	100	11	10	113
K50-125	NBR	PU	125	110	11	10	123
K50-125/1		PU	125	105	9,25	8,25	123
K50-125/2	NBR		125	110	10	9	123
K50-127		PU	127	107,95	12,81	11,81	125
K50-127/1		PU	127	107,15	18,06	17,06	125
K50-152		PU	152,4	134,94	20,05	19,05	150,4
K50-158		PU	158	146	9,5	8,5	156
K50-160		PU	160	140	15	14	158
K50-160/1		PU	160	140	9,25	8,25	158
K50-160/2	NBR	PU	160	145	11	10	158
K50-160/3	NBR		160	148	9	8	158
K50-160/4	NBR		160	145	10	9	158
K50-180		PU	180	160	13	12	178
K50-180/1 PU		PU	180	160	15	14	178
K50-200	NBR	PU	200	180	15	14	198
K50-203		PU	203,2	182,56	23,33	22,22	201,2
K50-250		PU	250	226	17	16	248
K50-254		PU	254	223,83	27,1	26,1	252
K50-320	NBR	PU	320	295	18	17	317

K50 is a single acting pneumatic piston seal designed to have asymmetrical profile with shorter and thinner dynamic lip

PRODUCT ADVANTAGES
• Secure seating due to the longer and thicker static sealing lip
• Low friction and good sealing performance due to the seal geometry
• Wide range of dimensions
• Simple groove design

APPLICATION
Standard pneumatic cylinders.

MATERIAL		CODE
NBR	80 SHORE A	NB8001
PU	80 SHORE A	PU8502

OPERATING CONDITIONS
NBR
MEDIA	Prepared , dried and de-oiled compressed air
TEMPERATURE	-30°C +105 °C
PRESSURE	≤12 Bar
SPEED	≤1.0 m/sn
PU
MEDIA	Prepared , dried and de-oiled compressed air
TEMPERATURE	-30°C +80 °C
PRESSURE	≤16 Bar
SPEED	≤1.0 m/sn
Note: The above data are maximum values and cannot be used at the same time.

SURFACE ROUGHNESS	Rmax
Sliding Surface ØD	≤0.4 μm
Groove Base Ød	≤10 μm
Groove Flanks B	≤15 μm
INSTALLATION K50 can be snapped by hand into the housing grooves provided. In case of using an assembly tools make sure that it is of soft material and have no sharp edges. Before installation the sealing element must be oiled with system oil. Special lubrication should be used on the sliding surface in case of having dried media. NOTES For special applications that require high temperatures , K50 can be produced in FKM material. We recommend using guide ring or guide rings with K50 piston seal.