KPB

Piston Rod Guide Strip
Piston Rod Guide Strip
   KASTAŞ NO a B (-0/+0,2) b
 KPB 2,5X10 2,5 10 9,8
 KPB 2,5X15 2,5 15 14,8
 KPB 2,5X20 2,5 20 19,8
 KPB 2,5X25 2,5 25 24,5
 KPB 2,5X5,6 2,5 5,6 5,4
 KPB 2,5X9,7 2,5 9,7 9,5
 KPB 2X10 2 10 9,8
 KPB 2X15 2 15 14,8
 KPB 2X20 2 20 19,8
 KPB 2X25 2 25 24,5
 KPB 3X15 3 15 14,8
 KPB 3X20 3 20 19,8
 KPB 3X25 3 25 24,5
 KPB 4X15 4 15 14,8
 KPB 4X20 4 20 19,8
 KPB 4X25 4 25 24,5
 KPB 4X9,7 4 9,7 9,5
 KPB-3X30 3 30 29.5
 KPB-4X10 4 10 9.8

KPB is a piston - rod guide strip designed to be used in heavy duty hydraulic and pneumatic systems.

PRODUCT ADVANTAGES
• High load bearing capacity
• Minimum static and dynamic friction coefficient for a minimum energy loss and operating temperature
• Able to be used behind the sealing element on dry condition
• High dimension stability during the operating temperatures
• Easy assembly
• Wide range of dimensions
• Easy to use in all dimensions because of being strips

APPLICATION
Mobile hydraulics , excavators , mining equipment , marine hydraulics , presses and heavy duty cylinders.
MATERIAL   CODE
POLYESTER RESIN   PR6501
OPERATING CONDITIONS
MEDIA    Mineral oils      (DIN 51524) HFA ve  HFB
HFC
TEMPERATURE  -40°C   +120°C    -5°C   +60°C   -40°C +40°C
DYNAMIC CONTACT PRESSURE     ≤100 N/mm2 ≤100 N/mm2 ≤100 N/mm2
SPEED ≤1.0 m/sn ≤1.0 m/sn ≤1.0 m/sn
Note: The above data are maximum values and cannot be used at the same time. Surface contact pressure value is given for dynamic application and it is 330 N/mm2 for static applications.

    

SURFACE ROUGHNESS Ra Rmax
Sliding Surface  ØD-Ød ≤0.3 μm ≤2.5 μm
Groove Base  ØDb- Ødp ≤1.6 μm ≤10 μm
Groove Flanks  B ≤3.2 μm ≤12 μm
.

INSTALLATION
Easily assembled into the housing by hand. It is very important that the assembly tools must be of soft material and have no sharp edges. Before installation the wiper must be oiled with system oil.

NOTES
We recommend cutting the ready strip with 30° angle before using it. The length of the strip can be using the formula in section Calculation of Width & Cross Sectional Thickness of Guide Elements. The permissible sealing gap values of KPB guide strip is given in the below table.
 
PERMISSIBLE SEALING GAP
Cross-sectional thickness(mm) S(mm)
2.00 0.60
2.50 0.75
3.00 0.90
4.00 1.20
Note: The largest sealing gap value occurring on the non-pressurized side of the seal does have a vital importance for the function of the seal and in this respect it is quite important to use the S value lower than the above indicated numbers.